Coronado 15 project.

Post photos and descriptions of your ongoing projects here. No project is too big or too small.
User avatar
earlylight
Candidate for Boat-Obsession Medal
Posts: 342
Joined: Fri Dec 19, 2008 7:15 pm
Boat Name: Early Light
Boat Type: 1982 Sabre 34 MK I
Location: MD
Contact:

Re: Coronado 15 project.

Post by earlylight »

Agreed,, wrong bit for the job at hand.
Dick Coerse
Early Light
Sabre 34 MK1
Solomons MD

http://earlylight160.net76.net
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

Squidd wrote:Ummm...pilot points are for wood and non ferrous metals...
What? These are cobalt coated and rated for stainless. That's why I bought them. I'll have to learn more about drill bits.
Last edited by TampaBay on Fri Sep 27, 2013 1:41 am, edited 1 time in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

Four patches in total, they are cut from 1/8th inch sheet.

The trapezoidal patch (top) is the largest, the triangular patch (bottom) is the penultimate, but the best looking :)

Image
Last edited by TampaBay on Mon Nov 18, 2013 1:01 am, edited 3 times in total.
User avatar
earlylight
Candidate for Boat-Obsession Medal
Posts: 342
Joined: Fri Dec 19, 2008 7:15 pm
Boat Name: Early Light
Boat Type: 1982 Sabre 34 MK I
Location: MD
Contact:

Re: Coronado 15 project.

Post by earlylight »

My bad. I had never seen pilot point bits capable of drilling stainless steel. After a quick search on Google I found them. Thanks for enlightening me. :-)
Dick Coerse
Early Light
Sabre 34 MK1
Solomons MD

http://earlylight160.net76.net
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

This looks like the set I have.

http://www.tylertool.com/dewalt-dw1263- ... map=DW1263

They snap in an instant, that has been my experience. Also, when they cut through the bottom of the hole, they grab like a vise.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

The frame stiffeners ready to reinstall.
Image
Last edited by TampaBay on Fri Oct 18, 2013 8:23 pm, edited 1 time in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

Grade-5 and grade-8, these bolts get the hitch attached.

With some anti-seize and a little maintenance, these fasteners should last a lifetime.


Image
Last edited by TampaBay on Fri Oct 18, 2013 8:24 pm, edited 1 time in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

A long day of grinding: I cleared away rust from the frame (and everything else I could reach) with an angle grinder, a wire brush, and the shop-vac.

Image


Here the grinding is finished. This is a good time to inspect those back brakes.

Image
Last edited by TampaBay on Fri Oct 18, 2013 8:26 pm, edited 2 times in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

You might file this under "the answer to a question that nobody is asking." Here is a South African Gardenia seed pod, after a couple months in the sun.

Very fluffy, there must be some seeds in there someplace.

Image

Image
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

Almost ready to reinstall the hitch. Frame horns are cleaned and painted.
Image
Zach
Boat Obsession Medal Finalist
Posts: 684
Joined: Wed Jan 25, 2006 6:28 pm
Location: Beaufort, North Carolina
Contact:

Re: Coronado 15 project.

Post by Zach »

Have you tried POR15?

It is ridiculously tough paint for the underbody of cars, and wants a layer of flash rust to bond to. You can't break it beating it with a hammer, nor chip it off.

Zach
1961 Pearson Triton
http://pylasteki.blogspot.com/
1942 Coast Guard Cutter - Rebuild
http://83footernoel.blogspot.com/
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

I have heard about Por15. Other work is needed on the frame, and the Rustoleum is easy to remove. Plus, it's very cheap and has a low level of toxicity.

If I pull the bed, and the frame becomes accessible, that would be an ideal time for the Por15..

The truck sees only light duty (at most,) and it's kept in the garage. I'm curious to see how the Rustoleum weathers.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

I reinstalled the hitch closer in, under the truck. It could be installed 3 1/2" further out, but the frame and hitch are stronger with it tucked in closer.

With a cutoff disk, I removed a section of the bumper that fell directly above the ball's new location. In theory, the bumper is less strong, but in reality it's nothing but junk, and it's only good for license plate holding.

Before.

Image

After.
Image

Grind away sharp edges.
Image
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

Hitch is bolted in, and ready to go: Very glad to see this project completed.

See the red, white, blue and grey colors? The right paint scheme adds one extra ton of towing capacity to a Nissan hitch.
Image

Red = frame, blue = stiffener, grey = hitch, white = bumper bracket. I filled in the background so that the individual parts are easier to see.
Image
Last edited by TampaBay on Thu May 23, 2013 6:31 pm, edited 1 time in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

Yikes! This has to be replace. The new parts are on the way.

Center carrier bearing and brackets.

Image
User avatar
Squidd
Deck Grunge Scrubber
Posts: 34
Joined: Thu Dec 13, 2012 6:40 pm
Boat Name: Lazy Lady
Boat Type: Paceship PY26

Re: Coronado 15 project.

Post by Squidd »

You live in Florida...?

I'm surprised that truck has so much undercarriage rust...more likely to see that up here where they put salt on the roads 7 months a year...
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

Squidd wrote:You live in Florida...?

I'm surprised that truck has so much undercarriage rust...more likely to see that up here where they put salt on the roads 7 months a year...
Well, the truck was bought new in Louisiana, then went to Texas, and then to N. Carolina where my Father bought it from his friend. Dad took it to Northern New York then gave the truck to me. I took it to Boston and then brought it to Florida.

Yes, it does need work, but any truck that's been used continuously for 25 years (it's an 88) is bound to need a few parts repaired or replaced.
User avatar
Squidd
Deck Grunge Scrubber
Posts: 34
Joined: Thu Dec 13, 2012 6:40 pm
Boat Name: Lazy Lady
Boat Type: Paceship PY26

Re: Coronado 15 project.

Post by Squidd »

They're good little trucks and and seem to run almost forever...just surprised by the rust, but New York and Boston explain alot...
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

It was used in a couple "road salt" States.

In Florida, I used the truck (for a few years) to shuttle liquid chlorine from the pool store, to my house. That stuff is infamous for rusting out trucks.
Last edited by TampaBay on Thu Jun 26, 2014 11:03 am, edited 1 time in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

The new center support bearing was delivered.

Now, the drive shaft is disassembled on the living-room floor.

Image
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

Drive shaft is re-built: The first machine shop installed three new universals and the center bearing. This morning I took it to another shop, and they did the balancing and painting.
Image

The transmission end.
Image

The top is the differential coupling, and at the bottom, is the new center bearing.
Image
Last edited by TampaBay on Fri Oct 18, 2013 8:32 pm, edited 1 time in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

The carrier bearing: I used a wire brush and then some Emory cloth, to remove a few areas of rust; and finished with a coat of "rusty metal primer."

Image


Drive-shaft installed: Wow, what a project. My #1 test pilot is ready to RUN this fierce jalopy!

Image
Last edited by TampaBay on Fri Oct 18, 2013 8:34 pm, edited 1 time in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

The weather today is fantastic.

I drove to the boat launch, for a test tow (the boat launch is very crowded.) First, the ground wire was reattached, then I hitched up and hit the road. The maximum speed was 60mph (no problems with the truck or trailer.)

That is Sarasota Bay in the background.

Image
Last edited by TampaBay on Mon Nov 18, 2013 1:12 am, edited 2 times in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

I found this tarp at a "bring and take." Sheets of plywood span the cockpit, and prevent it from filling with rain.
Image
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

The old tarp is gone; relegated to yard duty (needed to drag piles of weeds and the like, out to the curb for pickup.)

This is a new tarp from Wal-Mart (12' by 24'.) Looking like a giant sleeping bag.


Image
Last edited by TampaBay on Fri Oct 18, 2013 8:39 pm, edited 1 time in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

Work begins on the tailgate.
Image

Adding one large rectangular patch (unless a better idea materializes within the next couple hours.)
Image
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

A tube of 5200 was dispensed across both surfaces (sanded and cleaned.) What I really needed here, was about 15 more clamps.
Three fairing strips were used to distribute clamping pressure; one strip is under the bricks, and two strips are at the bottom edge, sandwiching the old steel and the new.

Image
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

This is "slow cure" 5200. The instructions read "full cure in 7 days." The fast cure version completes in 24 hours.

I'll wait 48 hours, then it's on like Donkey Kong.
Image
Last edited by TampaBay on Fri Oct 18, 2013 8:41 pm, edited 2 times in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

The 5200 bonded poorly in a few spots with too much squeeze-out. Just to be safe, I installed eight sheet metal screws. I don't think I'll enter this truck in the Pebble Beach Concours D'Elegance (it's a very fancy car show.)

I fared in the new panel with Bondo and then glazing. The trim piece is painted flat black, and next comes a coat of primer.


Image
Last edited by TampaBay on Fri Oct 18, 2013 8:44 pm, edited 2 times in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

The gate is reinstalled. I'll attach the missing trim panel soon.
Image
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

I've been busy installing new front brakes.
Image

There isn't a replacement brake caliper within 7 counties of here. So, I'm rebuilding these.
Image

Cleaned up the hubs and installed new bearings (here, old races are punched out.)
Image
Last edited by TampaBay on Sun Jul 21, 2013 10:20 pm, edited 1 time in total.
Cruiser2B
Topside Painter
Posts: 134
Joined: Sun Jul 31, 2011 6:27 pm
Boat Name: Salacia
Boat Type: Alberg 30

Re: Coronado 15 project.

Post by Cruiser2B »

Love seeing your dedication to making old things new again...I am getting ready to pull the engine on my 66 VW beetle, driven daily.....but needs a freshen up.....way cheaper than a new car, just requires a bit of elbow grease..and its get 28-30mpg!
www.svsalacia.blogspot.com
Preparing to get underway!!
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

Thanks! The truck requires work now and again. As long as there's a use for the vehicle, it's much less expensive than buying new. I used to let the maintenance slide, but when I started towing, I got more serious.

This is what I'm replacing now (bearings and races, sway bar end links, rotors, calipers, pads, shocks, spark plugs and the PCV valve.

Image
Last edited by TampaBay on Fri Oct 18, 2013 8:46 pm, edited 1 time in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

The rebuilt and painted front brake caliper.
Image
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

I know people expect to see sailboats, but that will have to wait for tow vehicle repairs. :)

Truck updates: The idle problem is fixed (it was going Vrooooom----POooofff,, vroooooom----POooofff.) In other words; revving out of control then cutting out with a big backfire.

Test all sensors.

Image


Fixed a bad ground at the ECM (the computer.) This didn't solve the problem, but in any event it had to be done.
Image

The red wire is the new ground.
Image

Pinned the fast idle cam up and away from the throttle (see the shiny bolt just right of center.) The cam increases the rpm's at idle until the engine is warm; not needed in South Florida. So far the idle control is fantastic.
Image
Last edited by TampaBay on Thu Jun 26, 2014 11:16 am, edited 3 times in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

The inside of a throttle position sensor (mine.) If you step on your gas peddle you will rotate the throttle shaft. This sensor fits onto that shaft.

That red disk is rotated and the electrical signal generated (from 0.2 to 4.0 volts) tells the computer how to manage fuel and spark. Before you shell out 100+ clams for a new one, spray it with contact cleaner. Mine stopped working but after a cleaning it was back in service.

Image
Last edited by TampaBay on Fri Oct 18, 2013 8:55 pm, edited 2 times in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

How is everyone? The weather south of Tampa has started to cool and it's now possible to work without risking a heat stroke.

This is the 1st project I bumped into today, so here goes nothing.

The sunroof in the truck has a shade constructed of Masonite (my best guess.)

Image

The Masonite has disintegrated badly.
Image

I have both epoxy and polyester resin in the garage, and decided to give the polyester a try.
Image

Here it is clamped, weighted down, and covered with resin. I realize now that I should've mixed a test batch. The instructions call for 10 drops of hardener per 30mls resin, and I added 40 drops to 120mls (fingers crossed.)
Image
Last edited by TampaBay on Fri Oct 18, 2013 8:57 pm, edited 1 time in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

After 2 coats of resin, I wet out this length of fiberglass tape (4 inches wide, it runs from 7 o'clock up to 2 o'clock in this image.) This is strong enough for a sunshade. All it needs now is paint.

Image
Last edited by TampaBay on Thu Jun 26, 2014 11:19 am, edited 1 time in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

I spent some weekend time checking out the big multi-hull regatta on Sarasota Bay.

The 7th Buzzelli Rendezvous and the 2013 F18 Americas Championship Regatta.


A good fleet of Wetas.
Image

Many Windrider 17's (and one guy had a 16 so he missed out on some racing action.)
Image

On the beach.
Image

Windriders through the Australian pines. On the shore and enjoying a little shade.
Image

This class is fast. Check out these Formula 18s.
Image

Some of these boats are just out of the box.
Image

Coolest graphic work of the day.
Image

Black carbon fiber cloth, with a wood veneer overlay.
Image
Last edited by TampaBay on Tue Nov 05, 2013 8:37 pm, edited 2 times in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

I pulled the tarp, towed it to the car wash, then parked it here. I'm thinking about sanding off the non-skid from the foredeck, and then repainting.
Image
Last edited by TampaBay on Sun Apr 05, 2015 1:46 pm, edited 3 times in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

Picked up the paint and non-skid additive at Lowes. The thinner is for clean up.
Image
Last edited by TampaBay on Tue Nov 05, 2013 8:27 pm, edited 1 time in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

This was easier than anticipated. I sanded the surface, taped off the edges, and rolled on 2 coats. Then I sprinkled the non-skid additive onto the still tacky paint and rolled out the 3rd coat.

Image

Not perfect, but much better than expected.
Image
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

I made a trip to West Marine today, to buy a small can of West System 206 slow hardener. With thickened epoxy I faired in the blue areas and also a gouge on the port bow (see the red spots.) It's time to take a seat and enjoy some cool Florida weather.
Image
Last edited by TampaBay on Sun Apr 05, 2015 1:55 pm, edited 2 times in total.
seasailor55
Rough Carpentry Apprentice
Posts: 57
Joined: Wed Aug 31, 2011 5:32 pm
Boat Type: Cape Dory 22 Pearson Ensign

Re: Coronado 15 project.

Post by seasailor55 »

Nice job on the boat! You've put a lot of time and effort in a 15 footer and it shows. I tackled a similar project on a Cape Cory 22. The boat had a serious encounter with a dock in Galveston, Tx. during hurricane Ike and had soft spots in the deck. I recored sections of the deck, repainted the entire boat, then applied contrasting non-skid to the deck, using Hatteras White two part polyurethane tinted a sand color and mixed with polymer particles. Makes a world of difference wet or dry and covers the patched areas nicely. By the way, how does that Coronado 15 sail?
Attachments
Cape Dory Pictures 096.jpg
Cape Dory Pictures 089.jpg
Cape Dory Pictures 082.jpg
Cape Dory Pictures 095.jpg
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

Hello seasailor55,

The Coronado 15 sails well. It has plenty of sail and a comfortable cockpit. The hull and the foils have been faired, the boat has many new parts and it gets faster every year. The trailer is also in very good condition; it received a lot of time, and resources.

A closer look at the new fairing work: I removed this deck and installed a full bulkhead. It makes the hull many times stiffer, and when punching into large waves, no flex is perceptible.

Image

The paint: It's 12 dollars a quart. Because the boat spends most of it's time under cover, this paint could hold up for a long time. If after awhile I change my opinion, this small area can be sanded back to bare glass in half an afternoon and the project can restart from square one.
Image
Last edited by TampaBay on Fri Nov 15, 2013 10:31 pm, edited 1 time in total.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

Here it is, painted and ready to roll.

Image

Navy blue and white.

Image
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

I did some maintenance on the trailer this weekend. This rust and old paint was removed with a wire wheel.
Image


With the tire off, I replaced one bolt into the hub and hit it with the wires. Repeat times 10 and then attack the hub itself (repeat times 2.)
Image


Repainted and reassembled.
Image
Paulus
Skilled Systems Installer
Posts: 199
Joined: Mon Nov 22, 2010 12:05 pm
Boat Name: Guillemot
Boat Type: Mariner Ketch

Re: Coronado 15 project.

Post by Paulus »

The blue matches the boat... ;-)
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

Lots of left over blue paint.
TampaBay
Candidate for Boat-Obsession Medal
Posts: 391
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Coronado 15 project.

Post by TampaBay »

I really didn't want to do this, but the fairing work wasn't good enough. I ground off some paint and refaired the deck.
Image
Last edited by TampaBay on Thu Nov 28, 2013 11:35 am, edited 1 time in total.
Post Reply