Search found 220 matches

by preserved_killick
Sat Oct 12, 2013 7:52 pm
Forum: Boatbuilding and Repair Techniques
Topic: Triton mast beam attached how?
Replies: 8
Views: 3890

Re: Triton mast beam attached how?

Re-reading your post, I gather you removed the top fiberglass past the mast step. Sounds like a good plan.
by preserved_killick
Sat Oct 12, 2013 6:18 pm
Forum: Boatbuilding and Repair Techniques
Topic: Triton mast beam attached how?
Replies: 8
Views: 3890

Re: Triton mast beam attached how?

Rob, If I understand correctly, you used 6 short bolts that didn't penetrate into the mast beam, just the tapped epoxy. How wide an area under the mast step did you excavate? Did you stick to the perimeter of the aluminum mast step? Or wider? Did you do anything to beef up the support posts inside o...
by preserved_killick
Sat Oct 12, 2013 7:21 am
Forum: Boatbuilding and Repair Techniques
Topic: Triton mast beam attached how?
Replies: 8
Views: 3890

Re: Triton mast beam attached how?

One thing I was thinking, is that perhaps the bolts don't need to go all the way through the beam. If the bolts went in a couple inches, even with out a nut on the end, it would achieve the same goal? What I'm trying to avoid, is weakening the beam by drilling holes all the way through, and worse, d...
by preserved_killick
Tue Oct 08, 2013 8:55 am
Forum: Boatbuilding and Repair Techniques
Topic: Triton mast beam attached how?
Replies: 8
Views: 3890

Triton mast beam attached how?

Hi everyone, I'm replacing the mast beam on my Alberg 30: http://216.172.166.167/~seagrass/mast-beam-project/ http://216.172.166.167/~seagrass/wp-content/uploads/2013/10/clean1-768x1024.jpg My original mast beam had two long bolts that went down through the mast step, through the beam and ended with...
by preserved_killick
Fri Sep 28, 2012 5:27 pm
Forum: Questions and Answers
Topic: Triton ownsers - props catching seaweed
Replies: 1
Views: 1135

Triton ownsers - props catching seaweed

Quick question Triton owners, how much space is there between the outside edge of your boat's cutlass bearing and the front of the prop hub? I'm considering getting rid of my Campbell Sailor prop, due to the fact that it is always wrapped with seaweed. We'll go from 5 knots to 2 knots and the vibrat...
by preserved_killick
Thu Apr 19, 2012 8:52 am
Forum: Materials, Sources, and Innovations
Topic: Alumiprep 33 & Alodine 1201 in Maine
Replies: 1
Views: 2696

Alumiprep 33 & Alodine 1201 in Maine

Anyone in Maine or NH know a local source for Alumiprep 33 and Alodine 1201?


Jeff
by preserved_killick
Sat Apr 14, 2012 8:01 pm
Forum: Boatbuilding and Repair Techniques
Topic: Tapping threads in bronze
Replies: 4
Views: 2760

Re: Tapping threads in bronze

Finally got back to this. Using a flashlight and a mirror to see the back I was able to (painstakingly) file the steel out and just barely touch the tip of each thread in the bronze. Then was able to clean out the first few threads using a sharpened punch which let me start the tap to chase the stee...
by preserved_killick
Thu Apr 05, 2012 7:30 pm
Forum: Boatbuilding and Repair Techniques
Topic: Tapping threads in bronze
Replies: 4
Views: 2760

Tapping threads in bronze

This issue is sort of a pre-issue to recoring my cockpit floor. I had a heck of a time getting my tiller head off from the rudder shaft. https://lh4.googleusercontent.com/-83W5B7rWQSU/T3d9C0Llm4I/AAAAAAAAFX8/Qm9WGVlJw0g/s640/2012-03-31_17-05-09_368.jpg YYesterday, after days of heating, spraying, ta...
by preserved_killick
Thu Mar 29, 2012 12:05 pm
Forum: Boatbuilding and Repair Techniques
Topic: Cockpit Floor Re-Core question
Replies: 22
Views: 9409

Re: Cockpit Floor Re-Core question

I'd really like to save the topskin, but in the event that I can't..I'm working out the details on rebuilding the top layer of glass. My primary concern, is what to do with the volcano bump that rises up for the tiller. Could I cut the volcano out of the old top skin, bevel the edges and use it in t...
by preserved_killick
Thu Mar 29, 2012 9:58 am
Forum: Boatbuilding and Repair Techniques
Topic: Cockpit Floor Re-Core question
Replies: 22
Views: 9409

Re: Cockpit Floor Re-Core question

Zach,

Thanks for taking the time to reply. I've been reading through it, and re-reading to be sure I understand it all, and researching the details. Where to get stuff etc.

-jeff
by preserved_killick
Wed Mar 21, 2012 6:23 am
Forum: Boatbuilding and Repair Techniques
Topic: Cockpit Floor Re-Core question
Replies: 22
Views: 9409

Re: Cockpit Floor Re-Core question

Thanks guys. About the Circular Saw: I was thinking one of those battery operated mini circular saws might be the thing, but I no longer own one. The one I has was great for a couple of weeks until it died. I think I'll get an oscillating tool, and a thin wheel for my grinder. Not really looking for...
by preserved_killick
Tue Mar 20, 2012 8:41 pm
Forum: Boatbuilding and Repair Techniques
Topic: Cockpit Floor Re-Core question
Replies: 22
Views: 9409

Re: Cockpit Floor Re-Core question

I actually had great results with my oscillating saw. I did a total deck recore with 2 blades. I cut the top skins with plunge cuts and then used the same blade to clean up the rotten core and left over debris. I just used the sanding attachment to tidy up my toe/rub rails and grab rails for refini...
by preserved_killick
Tue Mar 20, 2012 6:50 pm
Forum: Boatbuilding and Repair Techniques
Topic: Cockpit Floor Re-Core question
Replies: 22
Views: 9409

Re: Cockpit Floor Re-Core question

Would an oscillating multi-tool work well for cutting the top fiberglass skin? I wouldn't mind a reason to buy one.

-Jeff
by preserved_killick
Tue Mar 20, 2012 11:30 am
Forum: Materials, Sources, and Innovations
Topic: Returning from the Cave and System 3 LPU and Clear Coat
Replies: 1
Views: 2819

Re: Returning from the Cave and System 3 LPU and Clear Coat

I painted my boat with System Three LPU summer of 2009 and it is holding up great. Up in Maine the boat is exposed to the sun May to November so the season is rather short. We put about 50 days a season on the boat. I also used the Clear Coat over some wood and while that seems to last many times lo...
by preserved_killick
Tue Mar 20, 2012 9:27 am
Forum: Boatbuilding and Repair Techniques
Topic: Cockpit Floor Re-Core question
Replies: 22
Views: 9409

Cockpit Floor Re-Core question

Hi Everyone, It's been some time since I've posted here. I've been simply enjoying the boat, and dealing with non boat projects. The cockpit floor of my Alberg 30 is soft, and needs to be dealt with. What I'd like to do (other than ignore it) is to carefully cut the top fiberglass skin with some pre...
by preserved_killick
Thu Sep 29, 2011 1:11 pm
Forum: Questions and Answers
Topic: Block brand advice
Replies: 6
Views: 1530

Re: Block brand advice

Garhauer
by preserved_killick
Tue Sep 13, 2011 4:39 pm
Forum: Boatbuilding and Repair Techniques
Topic: Moving hardware on the boom
Replies: 10
Views: 5327

Re: Moving hardware on the boom

Hey Brian,

Just checked out your blog, FROONIE looks beautiful. Nice work!

-jeff
by preserved_killick
Tue Sep 13, 2011 9:28 am
Forum: Boatbuilding and Repair Techniques
Topic: Moving hardware on the boom
Replies: 10
Views: 5327

Moving hardware on the boom

I need to remove 4 small pad-eyes from my aluminum boom, and add a 4 more in different places. The current pad-eyes are rivited to the boom. With the new hardware I'll drill and tap for SS bolts which will be Lanocoated. What's the current thought on filling holes? Tap and plug with something? These...
by preserved_killick
Thu Aug 18, 2011 4:29 pm
Forum: Forum Rules, Registration Information, and Posting Instructions
Topic: Site move
Replies: 20
Views: 7821

Re: Site move

Maybe too /much of a tangent, but as a new smartphone user, what is the advantage of these mobile formats? I'm accessing the board on my phone just using the usual interface, and it seems fine, but maybe I just don't know how much better it could be? The screen is formatted for a phone's screen, mu...
by preserved_killick
Thu Aug 18, 2011 6:58 am
Forum: Forum Rules, Registration Information, and Posting Instructions
Topic: Site move
Replies: 20
Views: 7821

Re: Site move

Kurt, Thanks for doing this. Would be a shame if this forum were to go away. After the move, would you consider adding Tapatalk? It's a smart phone app that gives a great interface for smart phone users to check out forums on their phones. I use it for a number of forums. Granted, I don't know what'...
by preserved_killick
Wed Aug 17, 2011 10:10 am
Forum: Questions and Answers
Topic: Purpleheart
Replies: 10
Views: 2007

Re: Purpleheart

I had some Mangaris (red balau?) left over from a deck project I did. I ran it through the planer and it's a close match to the African $$ mahogany I bought from the exotic wood yard. If anything the color is more consistent than mahogany, a touch darker. Mangaris feels denser, tougher than African ...
by preserved_killick
Wed Aug 17, 2011 8:42 am
Forum: Questions and Answers
Topic: Purpleheart
Replies: 10
Views: 2007

Re: Purpleheart

I think the wood used is personal preference. I'm too cheap to buy Teak, I've been happy with the mahogany I've used. Epoxy then varnish: I initially did that with a number of projects thinking it made great sense at the time. For most of what I did, I regret the epoxy as a complete coating. I've fo...
by preserved_killick
Wed Aug 10, 2011 12:35 pm
Forum: Sailing and Cruising
Topic: Need Suggestions for Summering in Maine
Replies: 4
Views: 2372

Re: Need Suggestions for Summering in Maine

Hi Jay, I too need high speed internet for work, and I've not found a marina/ boatyard in Maine that has a wifi signal good enough for work, especially from the boat. The further down east you go the worse it gets. In Maine, most of the marinas/boatyards are small operations and keeping a good wirel...
by preserved_killick
Thu Jun 30, 2011 12:37 pm
Forum: Sailing and Cruising
Topic: Getting to Bath, ME by boat
Replies: 4
Views: 2349

Re: Getting to Bath, ME by boat

Thanks Case. I had a feeling that was the case. I do trust my engine, but not the way the boat handles in currents. I've been surprised by how my boat veers around even getting into Robinhood from the Sheepscott when there's a bit of a current. And that's the easy part. Part of what had me curious w...
by preserved_killick
Wed Jun 29, 2011 6:48 am
Forum: Sailing and Cruising
Topic: Getting to Bath, ME by boat
Replies: 4
Views: 2349

Re: Getting to Bath, ME by boat

Thanks Paulus, At this point I'd rather satisfy my sense of adventure pushing the limits with my other toys! On this stretch of water I think it prudent to proceed cautiously with as much beta as possible. I can't find first hand experience of anyone who has done this by sailboat, just lots of peopl...
by preserved_killick
Tue Jun 28, 2011 5:51 pm
Forum: Sailing and Cruising
Topic: Getting to Bath, ME by boat
Replies: 4
Views: 2349

Getting to Bath, ME by boat

I'd like to visit Bath by boat, but from what I've read in the Cruising Guide both the Kennebec and the alternate Hell's Gates seem a little dodgy. Most sailors I've talked to don't recommend it, but have not attempted it. Anyone have any experience with either route? Just how bad is it? Any local k...
by preserved_killick
Sat May 28, 2011 8:45 am
Forum: Questions and Answers
Topic: Engine control lever, seeking opinions
Replies: 2
Views: 571

Engine control lever, seeking opinions

I've got a single lever control for my vetus diesel that's seen better days. I'll need to replace it eventually so I'm looking now for options. Any recommendations? Single or dual? Teleflex has a sinde mount single that includes: "Includes neutral warm up capability". What exactly is that?...
by preserved_killick
Mon May 16, 2011 10:57 am
Forum: Boatbuilding and Repair Techniques
Topic: Looking for inspiration: what to do with the anchor locker
Replies: 4
Views: 1231

Re: Looking for inspiration: what to do with the anchor locker

I agree, but at this point I don't even have a way to hang anything. I sailed on a 30 foot wooden boat that had a small floor in the locker below the foredeck. The anchor rode would pass through a chain pipe and land in a nice wooden bucket. Other stuff could be in there, but he anchor rode stacked ...
by preserved_killick
Mon May 16, 2011 9:09 am
Forum: Boatbuilding and Repair Techniques
Topic: Looking for inspiration: what to do with the anchor locker
Replies: 4
Views: 1231

Looking for inspiration: what to do with the anchor locker

Hi everyone, In my Alberg 30, the area forward of the v-berth I call the anchor locker. In my non liner boat this area is just the insides of the hull as it tapers down to a tight little area just forward of the v-berth bulkhead. I store my anchor chain/rode in there, plus another anchor rode. The p...
by preserved_killick
Mon May 16, 2011 8:52 am
Forum: Boat Photos
Topic: New to me Alberg 30 #329
Replies: 7
Views: 2680

Re: New to me Alberg 30 #329

Fantastic! As a fellow Alberg 30 owner I love seeing pictures of other A30's.

I'm sure you must know about the Alberg 30 mailing list?

http://www.alberg30.org/lists/

-jeff
by preserved_killick
Sat Aug 07, 2010 6:13 am
Forum: Questions and Answers
Topic: Trailering - how crucial is it to use straps?
Replies: 12
Views: 1574

Re: Trailering - how crucial is it to use straps?

Here in NH & Maine, I understand it is a law.
by preserved_killick
Thu Jun 17, 2010 6:37 am
Forum: Questions and Answers
Topic: Sanding heat causes delamination?
Replies: 10
Views: 1142

Re: Sanding heat causes delamination?

(I'm not saying I agree with the actual information; just that I can see where one would think "Huh, if this person says it, maybe I shouldn't just toss it off without a second thought" and then would check in with the gang here.) I don't know much about lots of stuff, but there's a coupl...
by preserved_killick
Wed Jun 16, 2010 12:42 pm
Forum: Projects
Topic: Need ideas for companionway drop boards.
Replies: 10
Views: 1750

Re: Need ideas for companionway drop boards.

Thanks Rachel,

Unfortunately louvers are effective for what they do. I don't even mind how they look, I think they look better than the routered slots that are flush. I'm seriously thinking of a letterbox opening with a small roof over it.
by preserved_killick
Wed Jun 16, 2010 7:11 am
Forum: Questions and Answers
Topic: Sanding heat causes delamination?
Replies: 10
Views: 1142

Re: Sanding heat causes delamination?

I think this is total bunk. Personally I've sanded/ground big holes in the hull and while doing so stopped to brush away dust with a latex gloved hand and the surface just is not that hot. I've experienced way hotter fiberglass on a deck in full sun. For what it is worth, after trying a few methods ...
by preserved_killick
Tue Jun 15, 2010 5:53 pm
Forum: Projects
Topic: Need ideas for companionway drop boards.
Replies: 10
Views: 1750

Re: Need ideas for companionway drop boards.

Nice joinery Quetzalsailor! I had to Google Makore..pretty wood. I agree about air flow, I'd like as much as possible.
by preserved_killick
Tue Jun 15, 2010 9:29 am
Forum: Projects
Topic: Need ideas for companionway drop boards.
Replies: 10
Views: 1750

Re: Need ideas for companionway drop boards.

Rachel,

That's neat. I've never seen that before. It looks secure & dry, although I'd need screen for the Maine coast. Refinishing looks easy too.

-jeff
by preserved_killick
Tue Jun 15, 2010 8:37 am
Forum: Projects
Topic: Need ideas for companionway drop boards.
Replies: 10
Views: 1750

Need ideas for companionway drop boards.

My current companionway drop boards consist of two sections built door-panel style with the top section sporting a plastic window panel: http://lh4.ggpht.com/_DjiBX1vNLIU/SIu6QAb0_hI/AAAAAAAAA98/t3hzRq-E6Us/s800/img_3566.jpg I'm thinking of making a new set consisting of three sections so they stow ...
by preserved_killick
Sun Jun 06, 2010 5:48 pm
Forum: Projects
Topic: Spring Projects
Replies: 10
Views: 1799

Re: Spring Projects

I spoke with Norm at West by North West (guy who sold the the prop) about the coating and he recommended to use Pettit Zinc Coat Barnacle Barrier once his coating wears off. I'm not so sure I'll worry about it. Last season, my first, we had no fouling to speak of. The mooring is near a dam that rele...
by preserved_killick
Sun Jun 06, 2010 10:00 am
Forum: Projects
Topic: Spring Projects
Replies: 10
Views: 1799

Re: Spring Projects

by preserved_killick
Sun Jun 06, 2010 9:57 am
Forum: Projects
Topic: Spring Projects
Replies: 10
Views: 1799

Re: Spring Projects

Oh! I had a brain fart. AWABS is an acronym that's used for aircraft. Something interesting on hoseclamps. Last year the Coast Guard station in Boothbay had an open house, it was a drizzly rainy morning so we went for the tour. I got to check out their big rescue boat. The engines were huge, and abs...
by preserved_killick
Sun Jun 06, 2010 8:50 am
Forum: Projects
Topic: Spring Projects
Replies: 10
Views: 1799

Re: Spring Projects

AWABS?

Are you talking about my massive prop nut zinc? It's the only system that I could find that fits. This camp zinc has a brass washer inside that goes between the two nuts. Like a big bagel it covers both with just enough room to get the cotter pin on the back.
by preserved_killick
Sun Jun 06, 2010 8:38 am
Forum: Projects
Topic: Spring Projects
Replies: 10
Views: 1799

Spring Projects

I'm about to launch for the season and thought I'd post a few pictures of some spring projects I've completed. The first is a small project but one that I'm sure will significantly add to my sailing enjoyment: http://lh5.ggpht.com/_DjiBX1vNLIU/TAuL6ZMwMAI/AAAAAAAAEzI/Xz0rMLUZr2s/s800/IMG_5734.JPG A ...
by preserved_killick
Fri Jun 04, 2010 8:21 am
Forum: Questions and Answers
Topic: Aligning strainer with fixed flanged seacock.
Replies: 10
Views: 1128

Re: Aligning strainer with fixed flanged seacock.

Thanks Maine Sail,

I did notice that sweeping elbow. I find it amazing how much room he has there. In my Alberg I really need to use the Vetus shown since it has the direct down fittings. I just don't have the room side to side unless I mount the strainer in a crazy spot difficult to reach.

-jeff
by preserved_killick
Fri Jun 04, 2010 7:56 am
Forum: Questions and Answers
Topic: Aligning strainer with fixed flanged seacock.
Replies: 10
Views: 1128

Re: Aligning strainer with fixed flanged seacock.

Thanks Tim. Your argument makes sense to me. I've just installed a new internal water strainer, but went with the Vetus 330: http://www.jamestowndistributors.com/userportal/woeimages/vetus/large/11783.jpg Plastic, not bronze. I don't have the room (width) for a Groco or Perko bronze strainer due to ...
by preserved_killick
Fri Jun 04, 2010 6:20 am
Forum: Questions and Answers
Topic: Aligning strainer with fixed flanged seacock.
Replies: 10
Views: 1128

Re: Aligning strainer with fixed flanged seacock.

Tim,

No External Strainer? Is this common? In my limited experience I've not seen this in practice. That would make the seacock install much easier.

Gosh, is relying on just the one internal strainer enough? What if..a plastic bag gets sucked in? Would it get trapped in the hose?

-jeff
by preserved_killick
Thu Jun 03, 2010 6:45 pm
Forum: Questions and Answers
Topic: Aligning strainer with fixed flanged seacock.
Replies: 10
Views: 1128

Aligning strainer with fixed flanged seacock.

I'm about to install a nice flanged seacock to replace a ball valve for my engine water intake. One thing that occurred to me that might be a problem is aligning the strainer. If the seacock is fixed to the hull (bolted), then what happens if you bottom out the threads on the strainer/through-hull a...
by preserved_killick
Tue May 18, 2010 1:27 pm
Forum: Questions and Answers
Topic: ?? How to Make a Dull Hull Shiny ??
Replies: 5
Views: 970

Re: ?? How to Make a Dull Hull Shiny ??

Hi Osprey410,

Gelcoat I'm assuming?

There's some good reading on the subject here:
http://www.sailnet.com/forums/gear-main ... h-wax.html

Lots of work.

-jeff
by preserved_killick
Tue May 11, 2010 7:34 am
Forum: Questions and Answers
Topic: I need a fix for my main hatch
Replies: 10
Views: 1008

Re: I need a fix for my main hatch

Thanks for the advice guys. I was able to move the ovals inboard, to a measurement less than the width of the tracks. To install I removed one track, then reattached by sliding the hatch forward and back to sink the screws. Feels more secure now.