Bristol 27

Post photos and descriptions of your ongoing projects here. No project is too big or too small.

Re: Bristol 27

Postby Lloyd » Sun Sep 23, 2012 8:02 pm

It's been a little while since any work has been done, but the summer heat is easing a smidge and I've started back. I got the old 1 1/2" seacock/thru-hull for the sink drain cut out. I beveled out the sink drain hole and the hole for the old 3/4" water intake on the other side. Epoxyed on four layers of biaxel on the out side of the hull on both holes today.
holes filled.JPG
holes filled.JPG (58.04 KiB) Viewed 5361 times

engine string.JPG
engine string.JPG (47.47 KiB) Viewed 5360 times

Also back to scratching out the cracks in the head liner and filling with epoxy. (no pictures)
Hope to start to work on her a little bit each week for a while now.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby TampaBay » Mon Sep 24, 2012 3:05 pm

You can say that again about the heat. I think I could get outside today for 20 minutes, and not succumb to dehydration.
TampaBay
Candidate for Boat-Obsession Medal
 
Posts: 393
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Bristol 27

Postby earlylight » Mon Sep 24, 2012 5:21 pm

70 Degrees F and sunny here in Maryland right now :)
Dick Coerse
Early Light
Sabre 34 MK1
Solomons MD

http://earlylight160.net76.net
User avatar
earlylight
Candidate for Boat-Obsession Medal
 
Posts: 349
Joined: Fri Dec 19, 2008 7:15 pm
Location: MD
Boat Name: Early Light
Boat Type: 1982 Sabre 34 MK I

Re: Bristol 27

Postby Lloyd » Mon Oct 01, 2012 1:14 pm

Last week I finished off filling the two thru-hull holes. Now I was able to start on the engine beds.
IMG_0272.JPG

I managed to get two pieces epoxyed into place on each side after cutting them out and fitting them. Today I put the third one in on each side. One more to go, then tabbing them.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Sun Oct 14, 2012 7:14 pm

Still working on the engine beds. After getting all four plywood blocks epoxyed into place I cut out two layers of biaxial tape (one 6" and one 4").
IMG_0279.JPG

I then epoxyed them in place. I used the extra epoxy to coat all the plywood also.
IMG_0280.JPG

I plan on covering the engine beds with one layer of biaxial cloth lapping down over the tabbing holding them in place.
So while all that was wet I started on the starboard battery box. It is located in the starboard cockpit locker (forward end) aft of the ice box. This one will hold two 6 volt batteries. Most of the pieces are cut out, except the lid. Still have to glue-screw into place.
IMG_0281.JPG

IMG_0283.JPG

I am waiting on a few parts for the head and poobox (thru hull, valve, thru hull for the box) to come in so I can continue work there. If it will fit I want to put the thru hull-valve beside the head.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Sun Feb 10, 2013 10:23 pm

I haven't done any work on the boat since last fall. Saturday I decided to something, so I cleaned up an area.
Star. Settee Back 2.JPG

Star. Settee Back 4.JPG

Then I put two coats of primer on.
Star. Settee Back 6.JPG

Star. Settee Back 7.JPG

If nothing else that made it look better. I hope to get a coat of finish paint on it soon.

Last fall I got the two battery boxes epoxied in place. One is on the port side and the other is on the starboard side. A couple of pictures from then.
IMG_0512.JPG

IMG_0515.JPG


Also last fall I had ordered some plumbing parts for the poo box and only part of the order was sent. The supply place no longer had the thru hull with out nut and a thru hull with a hose tail piece. They only sent a valve and a 90 deg. elbow. I also found out that 1 1/2" pvc spa hose I had bought at the local Lowes is about 1 5/8" and to big for the 1 1/2" fittings I had gotten. So no progress was made in the poo box plumbing area.

I hope a little more progress will be made this year.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Crazer » Mon Mar 04, 2013 1:25 am

I'm glad to see an update on this project. Just keep chipping away at the little things, a little work and here and there is much better than no work at all!
As eccentric as my boat.
Crazer
Master Varnisher
 
Posts: 122
Joined: Sun Sep 18, 2011 3:07 pm
Location: Ithaca, NY
Boat Name: Loon
Boat Type: Pearson Wanderer

Re: Bristol 27

Postby boyle » Sat Jul 27, 2013 1:22 pm

Just came across your posting on your boat Looks like it is progressing slowly but steadily. Though I must admit a lot faster than my rebuild has progressed.
I own a Bristol 24 that had been worked on poorly by a PO so it is even a larger project. Removed everything from the interior including the ballast and ground smooth. Stripped the hull and acquired a donor deck (to replace my badly damaged deck). Hope to get back to work on it this coming year and get it finished.
Keep the good work!
boyle
Bottom Sanding Grunt
 
Posts: 6
Joined: Fri Aug 13, 2010 10:18 pm
Boat Name: La Boheme
Boat Type: Bristol 24

Re: Bristol 27

Postby Lloyd » Sat Oct 18, 2014 9:37 pm

Well it's been awhile. Three weeks ago I got some free time so I decide to work on the Bristol. I had decided that I had put the battery boxes in wrong. I had set them up for the batteries to line up for/aft. I wanted them to line up side to side. So I cut them out.
IMG_1321.JPG
IMG_1213.JPG

I rebuilt them (added a fourth side), refit them and epoxied them back in.
IMG_1322.JPG
IMG_1338.JPG
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Sat Oct 18, 2014 9:53 pm

The next weekend I made the lids for both battery boxes and started painting them.
IMG_1339.JPG

I also started working on the port wench base. The wood on the underside had rotted out. I got it all cleaned up and cut all the blocks out. I epoxied in one of the new blocks.
IMG_1340.JPG

I went to mix up some more epoxy and was out. So I cleaned up and headed up to the house to put in an order. I ordered epoxy, biaxial cloth, 6 oz. cloth, 1 1/2" thru hull and some hose.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Sat Oct 18, 2014 10:22 pm

My order came in Friday so today I got some tabbing done on both of the battery boxes.
IMG_1352.JPG

Also got one of the bottoms epoxied in place.
IMG_1353.JPG

Finished epoxying in the blocks in the port winch base.
IMG_1351.JPG

Then I got the last layer of biaxial cloth on the engine beds.
IMG_1348.JPG

Hope to get a little more work done tomorrow.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Sat Oct 18, 2014 10:29 pm

Also have a question. Can these be used on a boat for the v-berth? Toppers from WalMart.
IMG_1345.JPG
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Crazer » Mon Oct 20, 2014 1:16 pm

You can order custom cut toppers for a little more from a variety of online stores. That might be a better solution just in terms of usability and aggravation. I plan to do the same thing on the Wanderer.

Thanks for posting updates, this forum needs more projects!
As eccentric as my boat.
Crazer
Master Varnisher
 
Posts: 122
Joined: Sun Sep 18, 2011 3:07 pm
Location: Ithaca, NY
Boat Name: Loon
Boat Type: Pearson Wanderer

Re: Bristol 27

Postby Lloyd » Mon Nov 03, 2014 11:14 pm

Work done two weekends ago.
I got a layer of biaxial cloth on the underside of the port winch base. Picture was before the epoxy was added.
IMG_1354.JPG

Water washed, sanded then put two coats of bilge coat paint on the engine base.
IMG_1381.JPG
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Mon Nov 03, 2014 11:32 pm

And then this past weekend.
A coat of paint on the inside of both winch bases after water washing and sanding.
IMG_1399.JPG

Some Poobox work.
Added a block outside
IMG_1388.JPG

and one inside the box.
IMG_1390.JPG

They are there to hold the thru hull fitting (bottom drain) on an angle for better hose attachment.
IMG_1391.JPG

IMG_1392.JPG

Then I cut the base for the Poobox for the new block on the outside.
IMG_1394.JPG

The hull thru hull is just sitting there in the picture (not installed yet) but that is where it's going to go.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Sat Nov 15, 2014 11:31 pm

Well the battery boxes are painted.
Starboard, two 6 volt batteries.
IMG_1521.JPG

And port, single 12 volt battery.
IMG_1525.JPG
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Paulus » Sun Nov 16, 2014 11:59 am

Can they breathe? You don't want to accumulate Hydrogen gas (lighter than air) during hard charging periods...
Paulus
Skilled Systems Installer
 
Posts: 199
Joined: Mon Nov 22, 2010 12:05 pm
Boat Name: Guillemot
Boat Type: Mariner Ketch

Re: Bristol 27

Postby Lloyd » Mon Nov 17, 2014 4:25 pm

No vents yet. I haven't decided how/where to vent them. The cockpit lockers are open to the motor/bilge areas right now. Any ideas are welcome.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Tue Nov 25, 2014 11:06 pm

Bad news. I always thought the bottom was in good shape.
IMG_1536.JPG

I was working on the starboard topsides sanding and decided I needed to get the bottom paint out of the way. So I sanded the top six inches along the water line. I didn't like what I was seeing and sanded a bigger area.
IMG_1538.JPG

And a close up.
IMG_1539.JPG

The gel coat is full of blisters and cracks. Oh NO.
So I tried to sand the gel coat off to see how deep they went.
IMG_1532.JPG

And what do I find? A big one. About two inches across.
IMG_1541.JPG

The little blisters do not go into the glass. The big one goes through the first and second layers of glass, as far as I can tell. Sounding some more of the bottom I found a couple more two inch ones. So the question now is, do I take all the gel coat off and then rebuild it back up with an epoxy barrier coat after filling the big holes with some glass?
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby TampaBay » Thu Nov 27, 2014 12:28 pm

I've been reading through a few articles on the subject. Two authorities on the subject are David Pascoe, and Jan de Groot. Both of these guys have a lifetime of experience.

Jan: http://www.yachtworld.com/mustangyts/mustangyts_5.html

David: http://www.marinesurvey.com/surveyguide/
http://www.yachtsurvey.com/moreonblisters.html.htm

The general consensus seems to be repair as much as possible and continue on enjoying life. Also, you can consider yourself lucky that a previous owner didn't find the problem and then completely futz everything up with a mess of bad repairs. Even adding barrier coat is controversial; considering that laminate water intrusion is very likely to also be coming from inside the boat.

Here is a link to the West System blister repair guide. http://www.westsystem.com/ss/repairing- ... -blisters/
TampaBay
Candidate for Boat-Obsession Medal
 
Posts: 393
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Bristol 27

Postby Lloyd » Thu Jan 01, 2015 4:37 pm

I got some nice Christmas presents from the family for the boat.
IMG_1559.JPG

I guess I'll have to start working on the inside systems now.
They then asked how long it will take to get it floating and I just had to laugh.
Hope everyone had a Merry Christmas and looking for a wonderful New Year.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby TampaBay » Sat Jan 10, 2015 10:10 am

I'm checking out your Christmas loot. Can't see what that stuff is though, I think that the picture is just to small. I clicked on it and an image opened up, it was small too.

So what is that stuff?
TampaBay
Candidate for Boat-Obsession Medal
 
Posts: 393
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Bristol 27

Postby Lloyd » Sun Jan 18, 2015 10:29 am

Christmas things in the picture. Two Whale Gusher Galley Pumps for sink. One fresh and one for salt water. Two water Spouts for sink. One shower sump kit. Going to use it for the sink drain and the ice box drain. Power Distribution panel with eight positions, six breakers installed. And one battery main switch.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Mon May 25, 2015 8:58 am

Slowly sanding gelcoat off. I have gotten the starboard side mostly done. Have not gotten under the stands yet. Figure I will move the stands after I finish redoing the rest of the area. Have not figured out how to get under the keel and keel blocks. Might end up skipping that area.
IMG_1714.JPG
IMG_1715.JPG

Next up is to coat with epoxy, patch holes, fill/fair all the little holes, sand it all smooth, then build up layers of epoxy.
Then start the port side.
Sounds easy enough. Yea right.
I was so hoping to paint the topsides and deck this Summer. Guess that will happen next year if I am lucky.
On a side note. I might have gotten a place on the Coast on the water to keep the Bristol at. Looking at building a floating dock. Has anyone used the polyethylene floats for a floating dock?
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Cruiser2B » Sat May 30, 2015 11:20 am

Lloyd,

I feel your pain with the bottom. I too figured I would just sand paint off and be done with it but like you found an entirely new project. My Alberg 30 has issue with voids and pits between gelcoat and first layer of glass. Right now I am in the process of removing the paint after that I will decide on a path to repair.

Good Luck!
www.svsalacia.blogspot.com
Preparing to get underway!!
Cruiser2B
Topside Painter
 
Posts: 139
Joined: Sun Jul 31, 2011 6:27 pm
Boat Name: Salacia
Boat Type: Alberg 30

Re: Bristol 27

Postby galleywench » Wed Jun 03, 2015 8:01 pm

Grinding the bottom is just plain awful. I've done a lot pretty bad boat work in my travels and this ranks right up there with the worst. It sure does look nice a purty when you finish up though. Since you have time, break it up into manageable bites.
galleywench
Skilled Systems Installer
 
Posts: 194
Joined: Mon Jan 05, 2009 10:21 pm
Location: Canterbury, NH
Boat Name: Magic
Boat Type: Alberg 35

Re: Bristol 27

Postby Lloyd » Tue Jun 16, 2015 10:53 pm

Some more pictures of the work.
Bottom paint sanded off.
IMG_1567.JPG

Gelcoat ground off.
IMG_1584.JPG

Then sanded smooth. The hole in the picture is where the glass was bad all the way through the hull.
IMG_1591.JPG

Starboard side sanding done.
IMG_1714.JPG

After cleaning the dust off and acetone wiped the first coat of epoxy is put on.
IMG_1723.JPG

Then a coat of epoxy filler over all of it.
IMG_1726.JPG

Holes being patched with epoxy/cloth.
IMG_1725.JPG

Also started sanding the bottom paint off the port side. Rain was blowing in on the starboard side so I moved around to the port side and continued working.
Attachments
IMG_1734.JPG
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Sat Jun 27, 2015 1:31 pm

Back on the starboard side I used epoxy filler on some spots this past week.
IMG_1737.JPG

I water washed/scrubbed the spots then sanded them.
This morning I vacuumed, then acetone wiped the starboard side bottom.
Then I gave it three coats of epoxy.
IMG_1739.JPG

Next up is water wash/scrub the epoxy then give it all a light sanding. I hope I do not find anymore places that need filler. Then start the epoxy with aluminum power for the outer coats.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Tue Jun 30, 2015 8:46 pm

Update, no pictures.
Water washed/scrub the epoxy, then sanded it lightly, vacuumed it, acetone wiped it, then three coats of epoxy with aluminum powder. It all went well I thought. I checked on it late that afternoon and I find small air bubbles had popped up over the hole area. They were spaced out pretty well, so it was not a total failure. Oh well, guess I will give it another try.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Sun Jul 26, 2015 10:19 am

I gave the aluminum power coat that bubbled up a light sanding after water washing it. Then on the July 4th weekend I gave it two more coats of the aluminum power epoxy mix. The following weekend when I went to water wash it, it was still sticky. Crap. I did something wrong, what, I am not sure of. I am thinking that some how I didn't get the second coat on soon enough and that caused it not to cure right. Not sure. All I know is I had a big mess. So I started scraping and sanding the mess off and that has taken me a couple weeks.
So this morning I gave it a last quick once over sanding to see if I had gotten it all. Then wipe it down, acetone wipe it, and then one coat of epoxy. Hope this one cures right this time.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Cruiser2B » Sun Aug 02, 2015 5:23 pm

Lloyd,

thank you for posting your progress, and especially your success or lack of with the epoxy. I have just stripped down my Alberg 30s hull and am going to begin coating it in a few months when the humidity drops.

I love the B27, I used to sail with a guy that has one, Winter Dreams. We would have some fun racing them on Chesapeake during the winter.
www.svsalacia.blogspot.com
Preparing to get underway!!
Cruiser2B
Topside Painter
 
Posts: 139
Joined: Sun Jul 31, 2011 6:27 pm
Boat Name: Salacia
Boat Type: Alberg 30

Re: Bristol 27

Postby Lloyd » Sat Aug 08, 2015 9:43 pm

Thanks for the kind words, Cruiser2B. I've been following your blog about your boat and just saw your last post. Your bottom problem looks different then mine but sounds like it is caused by the same problem. Voids between the glass and gel coat. You see how I've been dealing with mine, is it the right way or the easiest, probably not. I think I could have just coated it to reseal the gel coat and been just fine. Good luck with repairing your bottom.

As for what I have gotten done. The last coat of epoxy cured just fine. After a week I water washed it, light sanding, acetone wipe then another coat of the aluminum powder/epoxy mix. After another week, today, water wash, light sanding, acetone wipe then a coat of epoxy, no aluminum powder. This might be it for this side for now till I move the boat stands. We'll see.

Small interior projects. I cut out a bottom shelf for the ice box and a couple of cleats to hold it up. Coated them with three coats of epoxy to seal them up. Also got the cleats epoxied into place.
Trimmed the head plywood base to allow a space for the thru hull on the left hand end of it. Also gave it three coats of epoxy.
Will take some pictures tomorrow if I remember.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Mon Aug 10, 2015 10:53 pm

Ok, I took a few pictures.
First one is a shot from the front of the new bottom.
IMG_1792.JPG

Then a shot from the back of the new bottom.
IMG_1793.JPG

Cleats being epoxied into place in the ice box.
IMG_1794.JPG

Then the cleats showing the drain under them. The drain is not epoxied in yet.
IMG_1797.JPG

New shelf in place in the ice box.
IMG_1796.JPG

The head base laid in place.
IMG_1800.JPG

And with the head sitting on the base.
IMG_1801.JPG

Also started grinding/sanding on the port side bottom.
IMG_1809.JPG

Picture of the voids I find under the gel coat (dark spots).
IMG_1806.JPG

And a void along the leading edge, port side (long dark spots).
IMG_1808.JPG

And that's it for now.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby pjesus » Tue Aug 11, 2015 3:46 am

Silently following... nice work.

Tell me more about the icebox. Are you gonna fit a standard one over the shelf or build a custom one?
User avatar
pjesus
Rough Carpentry Apprentice
 
Posts: 63
Joined: Thu Nov 05, 2009 1:37 pm
Location: Portugal
Boat Name: Jet Lag
Boat Type: 1982 B-Jet

Re: Bristol 27

Postby TampaBay » Tue Aug 11, 2015 11:30 am

Making good progress.
TampaBay
Candidate for Boat-Obsession Medal
 
Posts: 393
Joined: Wed Sep 30, 2009 3:46 pm
Boat Type: Coronado 15

Re: Bristol 27

Postby Lloyd » Wed Aug 12, 2015 6:04 pm

Pjesus, Was thinking, if you just looked back in the posting you would see what I had done to the ice box. So I looked back in the posting and guess what? I never posted anything about the ice box rebuild. It was one of the first things I did on the boat after I got it. It was probably before I started posting about the boat on here. But to answer your question, I pulled out the old ice box and built in a new one. I will try to dig up old pictures of what I did and post them some time.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Wed Aug 12, 2015 11:50 pm

Ok here we go. Building the ice box which was back in 2002/2003, I think.
First shot is how it was. The old box was side loading with a hatch from the cockpit. It had space under it for your feet laying in the bunk. It had a nice liner that I couldn't use. Very poor insulation.
DCP_1775.JPG

So I ripped it out.
Building icebox 1.jpg

Cut the end of the bunk to fit it in down to the hull.
Building icebox 3.jpg

Fitted in the plywood sides.
Building icebox 8.jpg

Added in cleats around the top.
dcp_2600.jpg

Then put in two layers of 2" foam. After that I put in 1/4" plywood to cover the foam. Covered the plywood with a layer of biaxial cloth. Faired that out and sealed it up with a couple coats of epoxy.
dcp_2601.jpg

New box.
dcp_2612.jpg

And a shot as it is now.
IMG_1815.JPG

I have a few more pictures of the hatch in the cockpit I will post tomorrow.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Thu Aug 13, 2015 1:55 pm

Taking out the cockpit ice box hatch and closing it in. Back I 2002/2003.
ice box removed.jpg

Laid in a layer of glass for the new inside surface.
Icebox deck 1.jpg

Put in a layer of balsa.
Icebox deck 6.jpg

Put a couple layers of glass, then faired it out. What it looks like now.
IMG_1813 - Copy.JPG
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby pjesus » Fri Aug 14, 2015 6:51 am

Hi Lloyd.

Thanks a lot for taking the time to find and share the pictures. It looks really nice! An icebox is something I'm missing on my boat but I haven't had the guts to build one yet.
Why did you decide to close the access hatch? Looks like a nice feature (I had never seen it before).

Lloyd wrote:It was one of the first things I did on the boat after I got it.

That's what I call good project management! At least you will have cool beer during the rest of the restoration! :)

Keep up the good work and sharing.

Cheers!
User avatar
pjesus
Rough Carpentry Apprentice
 
Posts: 63
Joined: Thu Nov 05, 2009 1:37 pm
Location: Portugal
Boat Name: Jet Lag
Boat Type: 1982 B-Jet

Re: Bristol 27

Postby Lloyd » Mon Aug 17, 2015 1:58 pm

Taking the ice box cockpit opening out was an easy decision. It just plain messed up that corner of the cockpit. It stuck up about three inches and was just in the way. Also, since I was rebuilding the ice box by lowering it there was no way to use it anymore. There is going to be a small instrument cabinet on top of the ice box where the hatch was.

As for work done this weekend;
Some grinding and sanding on Saturday.
IMG_1823.JPG

IMG_1824.JPG

And then some more grinding and sanding on Sunday also.
IMG_1826.JPG
Attachments
IMG_1827.JPG
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Sun Aug 23, 2015 5:53 pm

And a little more of the same stuff, grinding and sanding.
IMG_1831.JPG

IMG_1832.JPG

And I found an old patch job when I sanded the bottom paint off. You can see it in this picture. The gel coat was already gone and I could see where patches with cloth had been made. I sounded out the patches and about half of the area didn't sound good. It sounded like it wasn't adhered to the lead behind it. I will leave it for now and decide after I have finished getting all the gel coat off on this side if I will grind it all out and redo it. We will see.
IMG_1829.JPG
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Mon Sep 07, 2015 9:48 pm

More of the disappearing bottom gel coat.
IMG_1834.JPG

IMG_1837.JPG

IMG_1842.JPG

IMG_1844.JPG

IMG_1846.JPG

IMG_1847.JPG

So the grinding is done and a couple more hours of sanding and I'll have it done.
Then I found this old bad patch.
IMG_1841.JPG

It is about ten inches to the front of the port cockpit drain tube. Ground it out and it looks like an old filled in drain tube.
IMG_1848.JPG

It will get glassed over with the rest of the bad spots I've found on this side of the port bottom.
I will be glad to be done with the grinding/sanding on the bottom. It is a killer on the arms.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Sat Sep 12, 2015 10:58 pm

So I sanded off the bottom paint on one side of the rudder. It is very rough and appears to be not very smooth/flat. Did these boats come with wood rudders? It looks like someone put a layer of glass cloth on it and then didn't fair it out. I decided to pull the rudder off so I could work on it. First step was to take the foot/shoe off. The bolts came out easily and with a tap or two the shoe came off.
IMG_1849.JPG

One side of the shoe the bolt holes are recessed for flat head bolts and the other side the holes are threaded.
IMG_1850.JPG

The rudder had some slop fitting in the shoe. The rudder pin is about 7/8".
IMG_1851.JPG

And the shoe has a hole of about 1". So I might need to fit a bushing in the shoe to get rid of the slop.
IMG_1852.JPG

The next step on getting the rudder out is to take apart the stuffing box on the rudder shaft.
IMG_1863.JPG

And the big news is that I got through sanding off the gel coat off the port side bottom.
IMG_1858.JPG

Next up is putting epoxy/glass in the bad places that I ground out, then sanding them smooth. Then start the epoxy coating on the port side bottom. Also get the rudder off so I can work on it.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Sun May 14, 2017 8:35 pm

I'm still here. Sorry I gave up posting updates, If there is anyone left looking at this site to see this, I'll try to get things caught back up.
IMG_1865.JPG

I got the rudder off so I could work on it.
IMG_1905.JPG

I sounded the rudder, by tapping on it. I figured out where the glass skin was detached from the interior wood and drilled holes in it. I put epoxy in them and let it soak in.
IMG_1906.JPG

That then left small holes to fill in. I resounded it, added a few more holes, more epoxy. I kept doing that until it sounded good. Both side were done the same way.
IMG_2365.JPG

I then built up the rudder (on both sides) with epoxy filler to smooth it out. It had hollows and high spots to start with. I just kept adding filler and sanding, until it was smooth. Sealed it with epoxy, 2-3 coats of epoxy with alum. powder, 2-3 coats epoxy and done. Sorry no picture of the finished rudder. I still have to bottom paint it and rehang it.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Sun May 14, 2017 9:03 pm

IMG_2366.JPG

So I got the bottom reworked. Sealed it first with a coat of epoxy, then a coat of epoxy filler. Sanded it smooth then another coat of epoxy, 2-3 coats of epoxy with alum. power and then finished it with 2-3 coats epoxy.
IMG_2367.JPG

After I got both sides done I moved the jack stands and did the same to those spots.
IMG_2413.JPG

Stands moved.
IMG_2416.JPG

Bottom paint and gel coat sanded off.
IMG_2480.JPG

And all finished up.
I still have to put a coat of bottom paint on, to cover it all up.
If you notice in the last three pictures there's tape on the water line. I was working on the topsides also.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Sun May 14, 2017 9:29 pm

I finally gave up filling holes and such and put a coat of primer on.
IMG_2394.JPG

IMG_2400.JPG

All that did was make more holes and such show up. Did some more filling and sanding then more primer.
IMG_2494.JPG

IMG_2497.JPG

I lost count of how may coats of primer I put on. Sanding, primer, sanding, primer, seems like that's all I did for a long time. But now I think the topsides are ready for paint. I wish it was perfect but it will have to do.
IMG_2393.JPG

While I was working on the topsides I also got these pieces primed and ready for paint.
I decided to try the paint on these pieces first to try it out.
IMG_2502.JPG

So I rolled and tipped one coat of paint on. Got some orange peel. I gave them a light sanding with 320 grit paper. Then rolled and tipped a second coat on. That came out great except some dust and bugs, which I will have to live with. Doing it outside that's what you get. But I'm very happy with them.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Mon May 29, 2017 9:17 am

So it's Topside paint time.
IMG_2513.JPG

IMG_2514.JPG

IMG_2515.JPG

IMG_2516.JPG

IMG_2522.JPG

I put two coats on. Roll and tip.I think the first looked better than the second coat. Ended up with more brush marks on the second coat. It is very shiny, which shows every spot that I tried to fix. Every spot. Oh well, it's done.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Mon May 29, 2017 9:32 am

Then the following weekend it was bottom paint time.
Masking off.
IMG_2543.JPG

IMG_2544.JPG

I got one coat of bottom paint on.
IMG_2554.JPG

IMG_2557.JPG

IMG_2558.JPG

And not to forget the rudder.
Before bottom paint.
IMG_2550.JPG

And after.
IMG_2553.JPG

I used about half a gallon. Thought I would use up the bottom paint with a second coat but the rains set in. I'll try to get it one day after work this week. I hope.
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby Lloyd » Mon May 29, 2017 9:37 am

Then it's on to working (putting primer on) on the deck, cabin top and cockpit areas.
IMG_2508.JPG
Lloyd
Bristol 27, #200
Lloyd
Master Varnisher
 
Posts: 100
Joined: Sun May 13, 2007 1:04 pm
Location: Pelahatchie. Ms
Boat Name: Ella Marie
Boat Type: Bristol 27

Re: Bristol 27

Postby CapnK » Sat Jul 08, 2017 6:49 pm

Wow, looking nice, Lloyd, great job and good on ya for doing it! :)
Kurt and the CrewDogs
onboard Sundance,
'70 Alberg 30, hull #429
Still have Katie Marie,
'67 Pearson Ariel, hull #422
For Sale - Melelani,
'77 Islander 36, shoal draft

sailFar.net - Small boats, Long distances...
User avatar
CapnK
Site Admin
 
Posts: 67
Joined: Thu Aug 25, 2005 10:28 am
Location: Winyah Bay, Georgetown SC

PreviousNext

Return to Projects



Who is online

Users browsing this forum: No registered users and 1 guest

cron